Skip to content
Enjoy fast and free shipping on all orders over $89! Contact us (855) 424-4376
Enjoy fast and free shipping on all orders over $89! Contact us (855) 424-4376

Language

 

Spec Sheet   Install Manual

 Saniflo Sanishower

 The Sanishower drain pump is used to pump gray water away from a variety of fixtures in residential applications. The system is able to discharge the waste up to 12 feet vertical and/or 100 feet horizontal. Easy to install and small enough to fit underneath a shower base, it is ideal for medium duty applications.

 

The inside of the Sanishower is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the pump. When the water enters the Sanishower, it activates a micro switch in the pressure chamber, which in turn starts the motor.  The motor is sealed for life in an oil filled enclosure.  A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum.  Water enters the chamber and is pumped away into the sanitary sewer.  

The unit pumps the effluent upward to 12 feet and/or 100 feet horizontally (with gravity fall).  Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until water enters the unit again.  A normal operating cycle for the Sanishower can be as short as 2 - 10 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

In addition to sinks, the Sanishower will also accept and discharge the waste water from a variety of other sanitary fixtures such as: a shower, a urinal, etc.  When adding a shower, a base will have to be constructed.  This base should be made out of a 2" x 6" (minimum) on edge, to allow for the installation of a P-trap and the required 1/4”per foot gravity flow towards the pump unit.

The discharge elbow on the side of the Sanishower can be rotated 360 degrees to fit any type of installation required.  A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit.

This unit has been designed with a vent output on the top of the unit.  All plumbing codes require connection to a vent system.  Please note that the vent system should be a two-way air vent.  It is also highly recommended for the drain pump to be connected to a Ground Fault Interrupter (GFI) circuit.

The Sanishower is small enough to fit comfortably inside a kitchen cabinet or vanity or even under a raised shower base.

As a point of interest; quite a few pedicure manufacturers are putting the Sanishower inside pedicure chairs.  Due to its quiet operation and ease of installation, they have become the choice of OEM’s.

The Sanishower has been certified to American and Canadian Standards.  Electrical standard UL 778, CA:  Electrical standard CSA C22.2 

Part number 010
Max. horizontal discharge 12 ft
Max. vertical discharge 100 ft
Voltage 120 V
Frequency 60 Hz
Amperage 5.5 Amps (Max)
Motor 0.2 HP oil-filled thermally protected motor
Capacitor rating 25 microfarad
Operating temperature 104°F (110°F Max.)
Power cord length 48–1/2”
Noise level (measured at 3 ft.) ≤ 44 dBA (Lp)
Discharge pipe diameter 3 ⁄ 4 ” or 1”
Discharge rate at 15 ft @12 Ft : 14 GPM
Discharge rate at 3 ft 20 GPM
Shut-off head 26 ft
Normal running time 3-5 seconds (Short bursts)
Capacity 0.9 gallons / 3.4 liters
Inlets diameters 2” (sides)
Type of activation Membrane/microsw
itch
Shower/bath base height 5” min
Weight 12 lbs / 5.4 kg
Certifying agencies CSA (IPC, NSPC)

5 3/4" x 13" x 6 1/2"

Blog posts

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare